Over the last couple of months we have been
exploring the hardware calibration feature of the LG CX OLED displays and how to
optimise the picture for various uses. To do this we've been making use of
Portrait Display's Calman calibration software and the "AutoCal" feature that it
provides to directly calibrate the screen at a hardware level. This isn't the
only software available to hardware calibrate these screens, but it's the mostly
widely used and popular. We weren't intending to write a guide or article about this really,
other than maybe providing some results as an update and brief overview in our
LG CX OLED review. But the more we tested and experimented, the more we
realised how potentially complicated and confusing this topic can be. There is a
mass of great information out there on various forums and webpages, but it is
scattered around and hard to make sense of sometimes. There's also a lot of
great information on Portrait's website, but nothing that lays the process out
from start to finish.
So we thought we would
write this guide which covers everything you might need to know for a typical
calibration of the LG OLED TV's. It's not meant to be
definitive or include every possible option, and we aren't going to cover things
like complicated manual calibration steps or professional-usage setup. This is
meant as a guide that will hopefully be useful to your average owner who wants
to invest a bit of time and money in hardware calibrating the screen for their
normal uses like TV, movies and gaming. Our thanks to Portrait Displays for all
their time talking to us about this topic and answering our many questions as we
If you enjoy our work and want to
to the site are very welcome. If you would like to get early access to
future reviews and articles please consider becoming a
What You Will Need
An LG OLED TV (preferably 2019 models
or later) - we have written this guide while using the 2020 CX model but
equally this also applies to other 2020 models like the GX for example. It
should also apply to the 2019 C9 models, and this year's 2021 C1 range. For
a full list of LG OLED TV's that support LG AutoCal and this process see
Portrait Display's list here. Some
parts might change a bit but the gist of it should be the same. The 48" CX48
model has become particularly popular for use as a monitor given its
relatively small size (for a TV) and was introduced last year as the
smallest OLED offering in this space. We reviewed the
LG CX OLED back in October 2020 specifically looking at its use as a
desktop monitor by the way if you want to know more.
Calman calibration software - in
order to access the TV's hardware calibration feature you will need Portrait
Display's Calman software package. They have worked hand in hand with LG to
optimise this performance and process and their software provides full
control over the screen, it's settings and access to the hardware Look Up
Tables (LUT). The software carries out the so-called "AutoCal" process for
you on the screen once you've set a few things up.
The most popular choice specifically for calibrating LG TV's is 'Calman
Home for LG' which is
available from Portrait Display's website at a modest price of $145.00 USD
for a one year license. If
you have one of their more advanced
professional software packages such as Calman Ultimate ($2,995) then the
same process is available within those packages too, you don't need both.
For most general consumers looking to hardware calibrate their LG OLED TV
the Home package is what they need. For the 2020 CX models it needs to be
Calman 2020 v5.11.0 or newer but if you're buying it new you will get the
latest 2021 version anyway. If you already have a live license then you should be able
to download the latest version of the software from their website for free.
The software version is independent of the licence, you can always download
and use whatever the latest version is as long as your license is still
A pattern generator (included in the
TV for 2019 models and later) - this is the part that displays all the
colours and test patterns on the TV for the calibration process. Thankfully
for 2019 LG OLED models and later these are built in to the TV so you don't
need to worry, so that includes the 2020 CX models. This supports SDR, HDR
and Dolby Vision (DV) calibrations. If you are wanting to calibrate an
earlier TV like a 2018 model you will need to purchase an external pattern
generator for HDR and DV calibration as unfortunately there are no test
patterns built in to the TV. Portrait Displays have some available
on their website, we won't go in to more detail here about those as they
aren't needed for the 2019 models or later (C9, CX, C1 etc)
A USB stick with some (free) test
files on it - You will need to download this free
HDR sample video and this free
Dolby Vision sample video that are provided by Portrait displays (main
here). You might as well also download the
10 hour SDR video and put it on the same memory stick although if you're
connecting your laptop directly to the screen and running the software from
that you won't need it as it will already be in SDR mode there. The HDR and
Dolby Vision videos will be needed to put the TV in to the relevant HDR and
DV modes so you can calibrate them. Download them and save them on a USB
Optional but recommended are the free MediaLight Shadow Detail test videos
available here. Fill in the form and you should be able to download
those. Put the normal video versions on the same USB stick (you can discard
the Mac OS folder) and there should be four videos, for DV, HDR, HDR10 and
SDR. There are useful at the end of the calibration for tweaking and
improving the shadow detail. We will explain that in the process later. Plug
this USB stick in to the TV in to any of the ports and it should show up in
your list of inputs on the TV.
A PC or laptop that is connected to
the LG OLED TV you are going to calibrate - this should be preferably
with its own screen as you won't be able to use the LG TV while it's being
calibrated. This also needs to be connected to the same home network as the
TV, and the TV needs to be connected either using Wi-Fi or Ethernet to that
Connect a Laptop/PC to the Display
to need to be able to run the Calman software on a laptop or PC that is on the
same local network as the TV. You are also going to need to have your
calibration device ("meter") connected to this laptop/PC and nearby to the TV so
that it can take the measurements. The easiest method is to connect the
laptop/PC to the TV via HDMI and run dual screen in Windows, where you can see the output
on both the TV and the laptop. During the calibration itself you will not be
able to view the laptop/PC input on the TV itself, so you need a second screen.
For our calibration we had a PC connected to the TV but didn't have a second
screen near by, so we just used a free VNC app from an iPad to control and view
the software on the PC while AutoCal was running. Make sure you have HDR turned
OFF in Windows and are just running in normal SDR mode.
We won't run
through the installation of the software or your calibration device, that should
be pretty self-explanatory or you can refer to the Portrait Displays website for
Preparing the Screen for Calibration
carry out the AutoCal process to calibrate your screen there's a few things you
will want to do and check first in the TV menu:
recommended to give your TV a decent amount of time to "break in" after you
first purchase it. This gives the screen time to stabilise and a total usage
of around 100 - 200 hours is recommended before you bother going through the
calibration process. You can do it earlier if you want, and then revisit the
calibration process again later but it is probably worth waiting before
bothering as it can be time consuming to do this.
you're ready to calibrate we would suggest a reasonable warm-up period for
the TV of 30 minutes or more normal use
sure you've connected the TV to your Wi-Fi network and it is on the same
local network as your PC/laptop where the Calman software will be run from
need to make a note of your TV's IP address which can be found in the
network section of the OSD menu
that the firmware is up to date on the TV via the update section of the OSD
Picture menu turn OFF the Energy Saving settings. This avoids the screen
altering the luminance during calibration. If you like this ambient light
sensor you can turn it back on after the calibration if you want although
this has a big impact on HDR and DV brightness. We would recommend leaving
this off. From our testing the so-called 'Auto' mode (which is supposed to
dynamically control the OLED light level) seemed to dim SDR to about 130
nits regardless of the ambient light, both for day time viewing, or night
viewing with some lamps on. This in itself is ok for SDR, but for HDR/DV it
reduces the max peak brightness the content will reach which is really not
good! We measured a peak luminance of around 370 - 400 nits with this Energy
saving turned to 'Auto'. The other settings like low, medium and high are
just other preset caps to the OLED light setting. For HDR and DV you want
OLED light to always be at 100 if you want the screen to reach the maximum
peak luminance it is capable of. So having Energy saving enabled in any more
will not allow that. We would leave Energy Saving off for everything and
instead focus on calibrating the screen to a comfortable brightness, which
we will talk about later. This
energy saving setting spans across SDR, HDR and Dolby Vision modes so you
only need to disable it once.
in the 'general' section of the OSD menu turn off the 'AI brightness' setting
which also dynamically controls screen brightness depending on the
surrounding light in some modes. You may need to disable this in each SDR, HDR and DV
calibration modes when you come to calibrate each depending on the preset
you are configuring. For now disable it in all the modes you are
calibrating, and we will talk in the relevant section about which modes it
might be useful for, and what it does.
people like to turn off OLED protection features like the logo dimmer and
pixel shift feature while they carry out the calibration, although given the
actual test patterns you will display this seems a bit unnecessary to us
the Picture mode that you are going to calibrate
should be easy as you should have the Laptop/PC connected already and
running in normal SDR mode. For instance if you want to calibrate the
'Expert (bright)' mode, select that in the TV menu. You don't need to be
using the actual mode you're going to calibrate necessarily but it's
easier just to switch to that mode to start with. Also that way you're
in the mode once it's finished ready to enjoy your newly calibrated
get to the necessary Dolby Vision or HDR picture modes there is an
additional step needed, explained in the relevant sections later
OLED light setting in the selected Picture mode to your taste for your room
and lighting conditions. For SDR calibration there is a step within the
software to adjust this later too, so a good starting point is around 70 for
the OLED light setting (which should be around 200 nits). For the HDR and DV calibrations you won't need to do
this, as you'd want to leave OLED light set at 100 which is the default.
vital but maybe worth doing is to turn off
things like Noise reduction, Tru Motion etc and other image processing
enhancements. If you need to, you can turn some of these back on after the
calibration for the HDMI input you're using.
ready to calibrate the screen now! We have provided step by step guidance
using the Calman Home for LG software below which is the most common (and
affordable) package applicable here. The steps are very similar with their other
packages like Calman Ultimate but you'd need to first load up the 'display
specific - AutoCal LG' workflow from the main menu on those. Plug in your meter to the
laptop/PC then load up the Calman software.
You can do
these first few steps to connect the meter, source and display controls later as
part of the calibration process, but we personally prefer to do them before we
follow the calibration process. Either way is fine, and it's the same steps to
do them during the actual calibration process just at different points.
Configuring Your Calibration Device (Meter)
This step connects and sets up
the calibration device you are going to use for the process.
When you load up the Calman Home software you
should get the welcome screen like the above. The steps to the calibration
process are shown down the left hand side, or you can follow each of them
through with the 'next' button at the bottom right of the page.
Before you do that we need to configure and
set up a few key parts using the 3 currently yellow tabs at the top right. This
will set up the calibration device/Meter, connect the source test patterns for
measurement and give control of the TV to the software. There is also an
additional settings section under the gears icon. We will take you through each
step, don't worry.
The first step is to connect your calibration device
to the software. If you had this plugged in before opening the software it
should be auto-detected.
Open the first of the 3 tabs in the top
right hand area for 'Meter Settings' as shown
Instead of 'simulated meter' (which won't
be usable or do anything here) your calibration tool/meter should be listed
in the drop down box at the top of this section, select it here and the tab
should turn green to signify it's connected
If it's not there you can trigger a scan
for connected meters by pressing "find meter". In the window that pops up
tick the device you're searching for if it is listed and press 'search'. If
your device isn't in the list just press search anyway. After the search the
device should appear in the Meter selection drop down box. If that fails to
find it, try closing the software, unplugging your device, plugging it back
in then loading the software up again. We've found the detection of devices
very simple so it shouldn't cause you issues.
Back in the 'meter settings' tab you
should now be able to select your meter and the tab should turn green. Below
we have used an X-rite i1 Display Pro Plus
With the meter selected at the top there are
a few other things you need to configure for it. Some of the following settings depend on the
actual meter you are using but are likely to be the same, or at least our
explanations should hopefully help you choose the right option. These
settings are for the X-rite i1 Display Pro which is a commonly
used and recommended colorimeter for this process:
Select RAW XYZ for the meter mode
- this options adds a correction profile for the meter based on the screen you are
calibrating. It's not needed for spectro devices like the i1 Pro, but is
there for colorimeters like the commonly used i1 Display Pro. It
might seem logical here to select "OLED" as the Meter Mode
since we are calibrating an LG OLED TV here - however this is not correct
for the LG OLED TV's. In the 2020 Calman software this option was labelled
as simply "OLED" and so was confusing, but now in the 2021 update they've
helpfully renamed it to "OLED - (RGB)". That is because this correction
profile is designed for OLED panels with an RGB pixel structure. LG OLED
TV's actually have a WRGB pixel structure and so this profile won't be
appropriate. Calman are looking to add a specific profile for WRGB OLED in
the future, but for now the recommended option to select is Raw XYZ which
basically means no correction profile is used.
Select Sync Mode as 'Auto' - The
Auto mode is the recommended option for the greyscale 1D LUT calibration.
After that stage you could if you wanted go back to this menu and use the 'AIO'
option instead for the colour 3D LUT which will speed up the process a bit,
but we prefer to stick to the 'Auto' mode here for improved accuracy, even
at the cost of some additional calibration time.
At the bottom tick the box to enable
the 'Low Light Handler' mode - this is useful to optimise the darkest
measurements during the calibration. Recommended settings are 5 seconds
for the 'Low Light Mode' drop down, and then 1.0 cd/m2 as the 'Low
Light Trigger'. Note that the low light handler mode only works with the
'Auto' Sync mode and not with 'AIO' mode, another reason to use 'Auto'
We will discuss Meter Profiling
later section to be added in the future for those who might have access to a higher end
spectroradiometer device, which can help improve accuracy of your meter
further. There is some guidance for this on Portrait's website anyway if you
have access and want to improve things further.
Your meter should now be connected to the
software and the tab should turn green and look like the below (if you're using
the i1 Display Pro)
connection and configuration of other meters and devices you may need to check
out Portrait Display's
device resource centre for further information.
Connecting Your Source
This step connects the test patterns that
will be shown on the screen and used for the measurements and calibration. You
can use external pattern generators for this if you want, but we won't go in to
that here and they will cost extra money. Thankfully the LG 2019 OLED TV's
onwards, including the 2020 CX model and 2021 C1 model, have featured built-in pattern generators, so you can tell the Calman
software to access and use those which makes life simpler (and cheaper).
If you are calibrating the HDR or Dolby
Vision modes there is an extra step you need to do before connecting the source
to get the TV first in to the relevant HDR/DV mode. We will cover that later on
in the relevant sections. For now let's assume we're calibrating normal SDR
Click the Source Settings tab in the top
right hand area
Press the 'Find source' button.
In the pop-up that appears you need to
select LG as the manufacturer
Select the relevant model for your TV
- here we have selected LG - 2020/2021 OLED as we are calibrating an LG CX OLED
TV. We should note here that you might see some references online to
selecting your TV source as LG 2019 when calibrating the HDR mode, even if
your TV is a 2020 model. This relates to an issue with an older 2020 model
firmware where it was not generating the right HDR test patterns, but this
has been resolved and as long as your TV is running a recent/current
firmware you can select the 2020 TV model here without issue for all
calibrations (SDR, HDR and DV).
Enter the IP address for the TV that you
should have made a note of earlier from the TV network OSD menu and press connect
The screen will pop up a message with a
pin code, which you need to enter in to the prompt box on the software
The TV itself should switch in to a grey scale
pattern page which means the pattern generator is now active, at which point you will need to use your laptop or other
display to continue using and controlling the Calman software. This has
activated the internal pattern generator from the TV and you should see the
Source tab turn green and have 'LG' listed
Connecting the TV DDC
The last step is to connect the software to
the TV so that it can automatically control its settings, options and Look Up
Tables (LUT) for you during the calibration. This is done using the 'Direct
Display Control' (DDC) menu in the top right.
Click the 'Direct Display Control' tab in
the top right
Press 'find display'
In the pop-up select LG and the
relevant TV model. For the LG CX selection the options shown above
Enter your IP address for the TV again
(that you got from the network section of the TV OSD menu) and press
If you connected the source first then
you should not be asked to enter a pin from the TV, but if that pops up then
just enter the pin shown on the TV in the software and continue
The tab should turn green and confirm you
are connected to the TV (here it shows as LG 2020 OLED).
In this menu you can select the
picture mode you want to calibrate in the 'Display Mode Selection' drop
down. Only some of the TV preset modes are accessible for hardware
calibration but you have a good range you can use. You can also select the
mode you're going to calibrate later on in the software but it doesn't hurt
to do it here first. If the TV isn't already in that mode it will switch in
to it as well so you may see a visual change to the image on the screen.
Leave the other settings at default here
For SDR = Active Greyscale points for SDR mode
calibration = LG 26 pts SDR 16-255 (the default).
For HDR/Dolby Vision = active
greyscale points = LG 20 pts HDR (the default)
Don't bother increasing this to more
points like 42 for SDR for instance as that is really intended only for use with a professional meter
and if you use it with a normal colorimeter like the i1 Display Pro for
instance it can lead to less accurate results than 26 pts, and take much
longer to complete.
You can do a 'Full DDC reset' here
if you want, but it might be better to do it at the relevant step during the
calibration so that you can measure the pre-calibrated state properly and
compare it to your end results. Save this for later, we will explain what it
does at that step.
You shouldn't need to change much in the
general settings but you can also click the little gear icon in the top right
hand corner to access some further settings.
In the "Workflow Basic Options" section we
would ensure the following are selected:
Don't worry about setting the colour
space or gamma targets here, you can do that within the actual calibration
steps and most of it will be automatically handled for you anyway, just
leave them for now.
Luminance levels ensure 'Video (16 -
235)' is selected. Note that LG AutoCal is not designed to work for 'PC
(0 - 255)' mode. You can calibrate in the video mode anyway and if your
input device operates with full PC RGB just ensure that's switched on within
the TV menu and your device settings afterwards.
In the 'Application Measurement options'
section select the DelteE formula as 'de_ITP' for the highest level
of accuracy. This is the default for Calman 2021 software anyway, previous
versions of the software may have used a different default.
Everything else in these sections can be
left at default
After connecting your meter,
source and TV you're ready to carry out the calibration process itself. All
three of those tabs at the top right should be green now (ignore the fact they
aren't in some of our screenshots). Most of the calibration process is automated for
you, but we will talk through each step:
On the welcome page select OLED as the
screen type and SDR from the second drop down menu, press next
The 'session setup' page makes sure
you've got the meter and source connected properly (which you should have
done earlier), and then sets the targets for the calibration. If you haven't
got them connected, using these options here follows the same process
basically as we did earlier.
Colour space for SDR calibration =
Gamma formula = Power, then enter the
value as 2.2. This is our preferred gamma for daytime and evening usage,
but if you want to use the screen in a really dark room at night you could
enter 2.4 instead. Some people like to calibrate one mode like 'Expert
(bright)' for daytime use, and another like 'Expert (dark)' for evening use.
Whitepoint = D65 (which is 6500k)
Press next at the bottom to proceed to
the following section
Here you will be able to take measurements of
the screen before the calibration so you can compare before and after results.
If you have done a 'full DDC' reset earlier when we were connecting the TV
controls, this default performance of any' SDR mode will be really
poor. We get high dE errors for colours (6.4 average) and greyscale (8.6
average) so clearly this is going to need correcting. You might not have done
the full DDC reset yet though, so if not it will measure the current settings of
the mode you've selected.
Press the 'read series' button (which
looks like a capital H) in the bottom right hand corner to take these
pre-calibration measurements. It should take around 5 minutes. Once
finished, press next.
You can connect the TV here if you have
not done so already - which we did within the DDC tab at the top right
You can also perform the full DDC
reset here if you didn't do that earlier. No need to do it again if you
did. This step is necessary as it will
reset the picture mode selected that you are going to calibrate to panel
native settings, preparing it for the AutoCal process. This is a step beyond
just resetting the preset mode in the TV menu which would only restore it to
the factory calibrated profile. This Full DDC reset removes that factory
profile and starts everything from new for the selected picture mode.
Obviously you don't want to do this for any modes you are keeping, and only
do it is you're going to perform an AutoCal completely. The Native mode has
really skewed RGB balance, looks too cool/blue and has large dE errors for
greyscale and colours by default. Doing the full DDC reset sets it up ready
for the AutoCal process. Don't change anything in the TV OSD menu once
you've done this.
Check you've selected the picture mode
you want to calibrate here - we are doing 'Expert (bright)' in this example
For SDR calibration leave the HDR box
Select BT.709 as the colour space
for SDR calibration (this is the same as sRGB gamut by the way)
On the next screen check the 'enable calibration' box.
This should pop up a message on the TV at the top right saying 'calibration
start' to signify that it is connected and being controlled by the software
for calibration. Click next at the bottom
In the 'luminance' section you can use the slider to change
the OLED light setting of the TV and control how bright you want it to be
for SDR mode. If you press 'measure luminance' the meter will take
measurements as you go continuously. This OLED light setting will depend on your ambient
light conditions, viewing distance and preferences.
If you're calibrating for daytime brighter viewing then
something that reaches around 200 nits after calibration is a common target.
For night time viewing maybe around 100 nits instead after calibration. So
if you're calibrating two modes, one for day and one for night you could do
something like that.
If you only want one mode and don't really want to have
to bother switching between the different presets at different times of the
day maybe target 150 nits, we found this a comfortable level for all day
usage as long as you have some lamps on when watching at night.
As the guidance says here, you want to get the
TV set to about 15% brighter than your target in this step to account
for the changes the following calibration sections will make. So if you want
to reach 200 nits after calibration, use the "OLED light" slider and
measurement step here to get the screen to about 230 nits. If you want to
reach 100 then aim for 115 here. If you want to reach 150 aim for around 172.5.
You will have chance to re-tweak this
after the calibration anyway, but get it close to what your target is as
it's recommended to get as near as possible first
It's not recommended to change the OLED light setting in the TV OSD
menu later on after calibration as it could impact other aspects of
the setup (gamma, colour temp, colours) a little. Although minor changes to
the OLED light aren't going to make a huge difference so you don't need to worry about that
too much. If you need to tweak the OLED light later on in real use that's
not a huge issue. If you plan
to enable the 'auto' energy saving feature (ok for SDR but really not good
for HDR/DV) then you also don't need to worry
about this step much, as that feature would help control the OLED light
setting using the ambient light sensor and could be useful for varying room
lighting conditions. For optimal accuracy it's not recommended to use that
energy saving feature as it alters the OLED light, but it is never going to
make major changes so won't impact things that much. Through our testing the
validated results were still very good even with auto energy saving enabled
We left this at 70 for now.
Click next to proceed
This is where the real calibration starts! On this greyscale
multipoint screen you need to press the 'AutoCal' button in the bottom
right corner (the circular arrow icon next to "123").
A pop up will appear asking you to confirm number of
greyscale points you want to calibrate, leave it as 26 and press continue
This process calibrates the 1D LUT and corrects the colour temperature, white point and gamma of the display automatically for
you, making adjustments to the screen's hardware LUT. It takes around 28
minutes with an X-rite i1 Display Pro
At the end the results should look a bit like the above. Note
the EOTF (gamma) curve for the monitor is not even visible behind the yellow
reference line. The RGB balance line is now flat at the 0 level and there
are very low dE for the greyscales too, almost impossible to see on the
Once this has finished, press next
The next step does the colour mapping and corrections to the
3D LUT, ensuring the gamut you've defined is achieved and colour accuracy is
Press the 'AutoCal' button in the bottom right hand corner.
Press the 'optimize' button which runs a few sample tests and determines the
optimal pattern delay speed for this process, and can help account for
varying meter specs. Elsewhere in this pop-up select the calibration type as 'Fixed Grid, 9 points'.
This is quite time consuming but should provide a high level of accuracy.
Selecting more points adds to the time and won't provide any major
improvements so is unnecessary. If you're wanting a quicker calibration then
the Lighting LUT option can be used and produces pretty decent results
This process takes a lot longer, around
40 - 50 minutes with the
X-rite i1 Display Pro
25. The brightness and contrast adjustment
steps of the 'dynamic range' page are not needed for LG AutoCal, they will
likely be removed in a future update to the software.
After the calibration you can also click the "100" patch at the bottom of the
screen and press the play button on the right. That will measure a single white
patch and on the screen it will confirm your peak luminance. You have the option
here to tweak the OLED light control using the slider to get back to your target
of 200 nits or whatever you'd targetted earlier.
Separate Shadow Detail Corrections Before You
The AutoCal calibration has ended,
but do NOT un-tick the 'enable calibration' box yet
disconnect the calibration session). We want to make some shadow detail
corrections before we finish. This will make corrections to the very darkest
shades to ensure you can see all the relevant detail in dark scenes. This
step is necessary because each OLED panel sample varies somewhat and in the very
darkest tones it's hard for AutoCal to do this for you.
First we need to disconnect the screen's pattern generator '
source' for a moment to perform these checks. Press the source tab at the
top right and press 'disconnect'. The TV should end the patterns being shown
and return to your normal mode - probably the laptop screen you had
connected. Do not disconnect the DDC controls though or anything
You should have your USB stick already plugged in to the TV
with the Media Light shadow detail files on them. If not,
go back to
that step, download them and put them on a stick and plug that in to the
Change the input source on your TV to select the USB stick
that's plugged in
Navigate to the Media Light shadow detail folder and select
the SDR video file and play it. Put it on repeat if you need to, or we also
find pausing it on the 'flashed' image easy enough
You will need a dark room for these final corrections ideally
Get close up to the TV and you will see small flashing boxes
for different dark shades on the screen like in the above screenshot in a
greyscale, the idea here is to have box 64 as black, and everything below
that should also be black (everything < 64). But you should be able to
distinguish each box above that from 65 onwards. You may find that quite a
few of these shades above 64 are currently black as well, which is why you
need to do this shadow detail correction
While watching this test pattern video press the little screen icon in the top right
hand corner of the Calman software that says 'DDC'
This should pop up the DDC control menu, it should be on the
'RGB adjust' page as shown above, you need to use the scroll arrows to move to the
'display controls' menu page.
You should see some of your settings in
this page from earlier on (ignore the screenshot here). Scroll down to the bottom to the 'OLED shadow
For SDR leave 'OLED shadow detail point' set at
23 (note: this will be different for HDR and DV calibrations, explained
The setting to adjust is the 'OLED shadow detail value'.
While observing the test patterns on the screen move the slider up a fair
amount (200 or so to start with) and press the 'commit = on/off' button to
activate the change.
This should update the appearance of the grey shades on your screen. Having
made a fairly big change on the slider here, you will hopefully see a fairly
noticeable change on the shades. You need to then move it up or down,
pressing 'commit' each time, until you've honed in on the right level for
your panel. You can change this as many times as you want, so just
You want box 64 to be black and not show any "flashing"
while the video plays
Everything lower than 64 should also be
Everything above 64 should be progressively
brighter grey shades, with 65 being the first distinguishable shade you
can see flashing. You will find you can only make this just visible in
the flashing without impacting box 64 and below and it will be very
subtle. You will need to be in a dark room and up very close to the
screen to pick it out.
Use the 'OLED shadow detail value' slider to get to the
right level for your panel
Once you're happy with the shadow detail correction, close
the DDC menu and return to the main software
You should be back on this page, you can
now un-check the 'enable calibration' box to end the connection to the
screen. Note, do not ever go back in to try and tweak these shadow
details separately outside of the full calibration process as it will reset
your 1D LUT greyscale calibration as soon as you try!
If you want to complete the final
validation reports then you need to re-connect the source again that we
disconnected to do the shadow detail videos. Go in to
the source menu, select 'find source', choose your display and once
connected it should return back to the grey/white test pattern screen. Click
Now you're on the 'post-cal verify' page. Press the 'run
series' button in the bottom right (the one that looks like the capital H).
This will re-check the results and you should get low delta E errors now and
flat RGB balance graph. Once finished, press next.
The final 'side by side' page compares the pre-calibrated
state against the calibrated results for a nice quick verification of your
For those interested we also re-validated
the screen using our UPRtek MK550T spectroradiometer as the meter to confirm
that the white point (D65) had been met properly, and that the greyscale and
colour performance was accurate. i.e. we made sure that our spectro device
agreed with the results the X-rite i1 Display Pro was reporting above. They
did, since we had profiled our meter against this spectro first, so they
agreed nicely with one another. We will talk about Meter Profiling in a
future update. Without it you may find some varied results in visual
performance when using a non-profiled colorimeter on a screen like this.
Some people report some slight colour tints on white content. For optimal
accuracy you will ideally want to profile your meter against a spectro
reference device if you can.
That should be everything, you've calibrated in SDR for one of
the preset modes. Here we did it for the 'Expert (bright)' mode. You may want to
go in to each of your HDMI connections (TV, PC, built-in apps or whatever you've got connected
to the screen) and make sure that this Expert (bright) mode is selected for each
You can turn back on any video features you might want
like the motion features, increase
the sharpness control or whatever you like which are independent for each input
selection. So again make sure you've set those up for each input as you like
them. Do not change the settings for
brightness, contrast or anything to do with colour as this would disrupt your
calibration you've just spent all that time doing. While it's best to leave OLED
light at the setting you selected during calibration you can change it a
bit without impacting anything much as that just controls
the brightness of the pixels/screen. If you find you need to tweak this
afterwards that's ok. Again check this is set to the desired level for each
You can make the other changes above for each HDMI input individually
to your liking but the calibrated state applies for that preset mode where it's
selected for all the inputs, so you only need to do it once. The calibration is
at a preset mode level, not specific to any input source. The built-in apps like Netflix and Disney+ for instance
from a single profile, so again check that Expert (bright) is selected for them,
and you've got the other settings how you like.
An SDR Mode with wide gamut?
One final note is that maybe you also want a
mode with a wide gamut enabled but for SDR content. Perhaps you like the more
vivid and colourful look for certain content like anime or cartoons, accepting
that this won't be "accurate" to the defined SDR colour space but might be
desirable. If you want you can calibrate a different preset mode (we used 'SDR
Cinema') but this time select the target colour space as Rec.2020 instead of
BT.709. That will use the panels full native gamut. Follow the other calibration
steps and settings as above. At the end of it you should then have one mode
'Expert (bright)' configured for normal SDR content with a standard sRGB/BT.709
gamut, and another for SDR with a wide gamut.
Coming Soon to be added to this article
Dolby Vision Calibration
Meter Profiling guide and testing
If you enjoy our work and want to
to the site are very welcome. If you would like to get early access to
future reviews and articles please consider becoming a